BASIC ELECTROLYSIS CALCULATIONS This page looks at how to do routine electrolysis calculations. The Faraday constant The Faraday constant is the single most important bit of information in electrolysis calculations. Make sure you really understand the next bit. Coulombs The coulomb is a measure of the quantity of electricity. If a current of 1 amp flows for 1 second, then 1 coulomb of electricity has passed. That means that you can work out how much electricity has passed in a given time by multiplying the current in amps by the time in seconds. Number of coulombs = current in amps x time in seconds If you are given a time in minutes or hours or days, then you must convert that into seconds before you do anything else. For example, if a current of 2 amps flows for an hour, then: Number of coulombs = 2 x 60 x 60 = 7200 (60 minutes in each hour; 60 seconds in each minute.) That's easy! The Faraday Electricity is a flow of electrons. For calculation purposes, we need to know how to relate the number of moles of electrons which flow to the measured quantity of electricity. The charge that each electron carries is 1.60 x 10-19 coulombs. If you ever needed to use it in an exam, you would be given the value. 1 mole of electrons contains the Avogadro constant, L, electrons - that is 6.02 x 1023 electrons. You would also be given that in an exam if you needed to use it. That means the 1 mole of electrons must carry
This value is known as the Faraday constant. You may come across the formula F = Le, where F is the Faraday constant, L is the Avogadro constant and e is the charge on an electron (in terms of the number of coulombs it carries). We have just used that without actually stating it - it is basically obvious! The numbers we are using here are rounded off. The calculation just shows you how to work it out if you have to, but doesn't give the normally-used value. For exam purposes, the value of the Faraday constant is usually taken as 9.65 x 104 C mol-1 (coulombs per mole). This is another number you are unlikely to have to remember. That is 96500 coulombs per mole. So 96500 coulombs is called 1 faraday. Notice the small "f" when it is used as a unit. Whenever you have an equation in which you have 1 mole of electrons, that is represented in an electrical circuit by 1 faraday of electricity - in other words, by 96500 coulombs. | |
Note: I have said three times that a piece of information is likely to be given to you in an exam, but you need to be sure. Check your syllabus to find out what is contained in the Data Booklet you are likely to be given. You will normally find this towards the end of the syllabus. | |
Using the Faraday constant in calculations Electrolysis calculations are no more difficult than any other calculation from an equation. In fact, you may well have done them as a part of whatever course you did before you started doing A level. We will just look at four examples. Example 1 Calculate the mass of silver deposited at the cathode during the electrolysis of silver nitrate solution if you use a current of 0.10 amps for 10 minutes. F = 9.65 x 104 C mol-1 (or 96500 C mol-1 if you prefer). Ar of Ag = 108. The first thing to do is to work out how many coulombs of electricity flowed during the electrolysis.
Now look at the equation for the reaction at the cathode: Just as with any other calculation from an equation, write down the essential bits in words:
Now put the numbers in. 1 mol of electrons is 1 faraday.
So, if 96500 coulombs give 108 g of silver, all you have to do is to work out what mass of silver would be produced by 60 coulombs.
| |
Note: If your maths is really bad, so that you aren't happy about simple proportion sums, then think of it like this: If 96500 coulombs give 108 g, then 1 coulomb would give 108 divided by 96500 g. 60 coulombs would produce 60 times this amount. It doesn't matter in the least how you work this out - all that matters for your chemistry is that you get the answer right! | |
Example 2 This example shows you how to do the calculation if the product you are interested in is a gas. Calculate the volume of hydrogen produced (measured at room temperature and pressure - rtp) during the electrolysis of dilute sulphuric acid if you use a current of 1.0 amp for 15 minutes. F = 9.65 x 104 C mol-1 (or 96500 C mol-1). The molar volume of a gas at rtp = 24 dm3 mol-1. Start by working out how many coulombs of electricity flowed during the electrolysis.
Now look at the equation for the reaction at the cathode: Write down the essential bits in words:
Now put the numbers in. Two moles of electrons is 2 faradays.
So, if 2 x 96500 coulombs give 24 dm3 H2, work out what volume of hydrogen would be produced by 900 coulombs.
Don't quote your answer beyond 2 decimal places. The current and the molar volume are only quoted to that degree of accuracy. | |
Note: If you can't follow the last bit of the calculation: If 2 x 96500 coulombs give 24 dm3 H2, then 1 coulomb would give 24 divided by 2 x 96500 dm3. 900 coulombs would produce 900 times this amount. In other words, you are working out 24/(2 x 96500) and then multiplying by 900. It is a different order from the way it is shown in the simple proportion sum shown above, but the answer is still exactly the same. In addition, if you feel happier working out the value of 2 x 96500 before you do anything else, that's what you should do. As long as you get the answer right, nobody is interested in the exact way you handle the sums. | |
Example 3 This example shows you what to do if the question is reversed. How long would it take to deposit 0.635 g of copper at the cathode during the electrolysis of copper(II) sulphate solution if you use a current of 0.200 amp. F = 9.65 x 104 C mol-1 (or 96500 C mol-1). Ar of Cu = 63.5. This time you can't start by working out the number of coulombs, because you don't know the time. As with any other calculation, just start from what you know most about. In this case, that's the copper, so start with the electrode equation. Write down the important bits of this in words:
Now put the numbers in. 1 mol of electrons is 1 faraday.
You need to work out how many coulombs give 0.635 g of copper.
| |
Note: And again, if you still don't like simple proportion sums: If 2 x 96500 coulombs give 63.5g of copper, then you would get 1g of copper if you divided the 2 x 96500 coulombs by 63.5. 0.635 g would be produced by multiplying this by 0.635. | |
Now what? You know how many coulombs you need, and you know what the current was in amps. You have got all the information you need to work out the time.
Don't waste time trying to convert that into minutes or hours (unless the exam question specifically asks you to). Example 4 Another gas example: Calculate the volume of oxygen produced (measured at room temperature and pressure - rtp) during the electrolysis of sodium sulphate solution if you use a current of 0.50 amp for 30 minutes. F = 9.65 x 104 C mol-1 (or 96500 C mol-1). The molar volume of a gas at rtp = 24 dm3 mol-1. Start by working out how many coulombs of electricity flowed during the electrolysis.
Now we need to look at the equation for the reaction at the anode. Unfortunately, there are two ways of looking at this, and you may come across either of them. The first one releases oxygen from water molecules: The alternative way releases oxygen from hydroxide ions from the ionisation of the water: Write down the essential bits in words. Both ways of looking at it say the same thing:
Now put the numbers in. Four moles of electrons is 4 faradays.
So, if 4 x 96500 coulombs give 24 dm3 O2, work out what volume of oxygen would be produced by 900 coulombs.
Don't quote your answer beyond 2 decimal places. The current and the molar volume are only quoted to that degree of accuracy. | |
Note: I am not going to do this for you. If you have problems with this sort of sum, use the technique in the previous examples, and make sure you get the same answer. | |
Questions to test your understanding If this is the first set of questions you have done, please read the introductory page before you start. You will need to use the BACK BUTTON on your browser to come back here afterwards. questions on basic electrolysis calculations answers
To the Electrolysis menu . . . To the Inorganic Chemistry menu . . . To Main Menu . . . © Jim Clark 2017 |
Basic electrolysis calculations (2024)
Top Articles
Apex Teaching You Communication Skills, Retail Box , No Warranty On Software
Apex Teaching-You Feng-Shui Skills, Retail Box , No Warranty On Software
Novalene Gowdy
Hourly Weather Forecast for Berwyn, PA - The Weather Channel | Weather.com
Kyndryl and Excellium collaborate to help Luxembourg enterprises protect their critical assets
What Lies Behind Excellium Services’ Acquisition By Sonae IM - Silicon Luxembourg
Pacific Ocean - Trade Winds, Climate, Marine Life
Starrez Housing Uo
New Caney Isd School Supply List 23-24
The Colony by Ashton Woods
Latest Posts
Article information
Author: Mr. See Jast
Last Updated:
Views: 5966
Rating: 4.4 / 5 (75 voted)
Reviews: 90% of readers found this page helpful
Author information
Name: Mr. See Jast
Birthday: 1999-07-30
Address: 8409 Megan Mountain, New Mathew, MT 44997-8193
Phone: +5023589614038
Job: Chief Executive
Hobby: Leather crafting, Flag Football, Candle making, Flying, Poi, Gunsmithing, Swimming
Introduction: My name is Mr. See Jast, I am a open, jolly, gorgeous, courageous, inexpensive, friendly, homely person who loves writing and wants to share my knowledge and understanding with you.